DM-eng Designing products for the DeLorean automobile, new email [email protected]
Contact Email
  • Home
  • How Built
Picture
LED board for AC (HVAC) panel

Colors are more vivid than stock incandescent bulbs.  Only draws about 50 ma typical.  Available with green or blue LEDs.  Requires wiring, sanding paint off and metal cuts.
led_ac_panel_installation_instructions_v1.5.pdf
File Size: 1175 kb
File Type: pdf
Download File


Picture
Solid state RPM relay
Runs cool and dependable.  Always will auto prime.  Has user selectable hot start fix.  OEM units are prone to broken solder joints.  Plug and play.

Contact Chris Miles (on facebook) for extra RPM cores
rpm_install.pdf
File Size: 88 kb
File Type: pdf
Download File

Picture
Solid State Fan Fail unit
Each fan now fused.  Returns the fan fail indicator operation.  OEM fan fail must not be used anymore.  Plug and play.
fan_fail_install_rev_k.pdf
File Size: 204 kb
File Type: pdf
Download File


Picture

Solid State Fan Relay

Delays fans for one second and keeps fan running for 20 seconds minimum.  That eliminates fans cycling when AC cycles.  Plug and Play.
fan_relay_install.pdf
File Size: 18 kb
File Type: pdf
Download File

Picture
Solid State Hot Start Relay
You won't need to do the "PLUG SWAP" anymore.  If you unplug your thermal time switch engine starts faster in the summer.  Plug and Play.
Picture
Microprocessor controlled idle ECU
User adjustable idle RPM.  Turns idle motor off when not at idle speed.  Can work without the idle switch.  Plug and play
idle_ecu_instructions.pdf
File Size: 376 kb
File Type: pdf
Download File

key_removal.pdf
File Size: 368 kb
File Type: pdf
Download File

Picture
Solid State Relays
Custom made from the Fan Relay boards.  Note solid state relays are polarity sensitive so headlight and blower relays are not interchangeable.
Picture
Dome Light Dimmer
Update: New rev F units can work with switching regulators.

Works with LEDs that don't have a switching regulator.  Also works with incandescent bulbs.  User can program, Battery saver mode (turns power off after 10 minutes) , Parade mode (Flashes door lights) or normal mode.  Requires wiring changes to install.
dome_light_instructions_021224.pdf
File Size: 339 kb
File Type: pdf
Download File

Picture

Picture

Front relay bank ground buss
The stock wiring is showing problems with age.  New buss has one wire crimped pins.
relay_buss_install.pdf
File Size: 47 kb
File Type: pdf
Download File


Microprocessor BI-directional driver

For driving two wire devices that need polarity reversal.
3 amp continuous rated for driving latching relays, actuators.
Picture

ELECTRONIC OTTERSTAT

Requires 4 wires into an unused relay socket
install_otterstat_rev_b.pdf
File Size: 1141 kb
File Type: pdf
Download File


Picture

Picture

Picture

DUAL SIDE MARKER FLASHER

Shipped with 12 inch wires.  You will need to cut and connect the 8 wires into your harness.
blinker_install.doc.pdf
File Size: 124 kb
File Type: pdf
Download File


LAMBDA RELAY

Runs cool.  The stock lambda relay runs very hot.
PLUG + PLAY

AUX RELAY

Very little heating.  Rated at 75 amps.

Picture

Picture

DOOR LEDS

You remove the sockets so the LEDs move away from the lens.  I can't get a good photo of them illuminated.  You would need to see these in person on my car.

FUEL GAUGE ECU

Unit will let you use another fuel level sender and drive the OEM gauge.
Contact Chris Miles (on facebook) for fuel pump hardware.

fuel_level_ecu_install.pdf
File Size: 224 kb
File Type: pdf
Download File


Picture

Picture

LAMBDA ECU

Plug an play.  Helps to eliminate idle hunt.  Requires your old unit to upgrade.

lambda_ecu.pdf
File Size: 220 kb
File Type: pdf
Download File


MINI LAMBDA ECU

mini_lambda_ecu.pdf
File Size: 303 kb
File Type: pdf
Download File


Picture

Picture

Picture

Picture

3D PRINTED HVAC FACE PLATE

Eliminates all light bleed from different colored LEDs. Printed with black resin and has walls to block light.

PIN EXTRACTOR

For the round 3 mm pins and sockets.  The sockets still require work to remove.  Problem is the socket design will not let it compress the locking fingers.

GEAR SHIFT BALL

3D printed with epoxy decal.  Will never rub off.

DOOR LOCK ECU

Very low standby power.  No sticking relays like OEM.  No connector supplied.  Splice your old one or replace with another connector.


door_lock_install_instructions.pdf
File Size: 501 kb
File Type: pdf
Download File

Powered by Create your own unique website with customizable templates.